Many bar code printers are actually connected in some operations and principles, so today Xiaobian gives you a general summary of bar code printers from label production and saving to printing common faults and accessories damage, etc., I hope to help everyone.
1. The label can't be saved after modification. Pressing Save will bring up a warning dialog box. After pressing OK, the software will be closed.
Cause: Caused by an incorrect operation that was modified directly on the label when the user modified it.
Solution: Modify it according to the correct modification method. Double-click the content you want to modify, and modify it in the dialog box written in the original layout. It is not allowed to modify directly on the label. After this modification, it will return to normal.
2. All the indicators flash when the printer is printing and cannot measure paper (Zebra barcode printer)
Cause: The sensor is faulty.
Solution: Clean the sensor surface or replace the sensor.
3. The printer is not in place when printing small labels, and the printed content is always biased upward or downward.
Cause: The label is too small and it is difficult for the sensor to sense the paper.
Solution: The height of the general label should be at least 10 or more to locate, otherwise the label should be offset. When setting the label, set the height of the label to be about 5 mm larger than the actual label, and then set the offset of the label according to the specific offset.
4, the font is clear when printing, the barcode is not clear
Reason: The barcode content is too much and the density is too small.
Solution: Shorten the bar code content or increase the bar code density. For 200dpi and 300dpi machines, the bar code density is generally above 7mils, ie the scale factor is 2 or more, and the printed bar code is clear.
5, when printing labels, some words can not be printed
Cause: The print head is dirty and the layout is incorrect.
Solution: Clean the print head; also see if the words to be printed are overlapped during the typesetting, and the layout is re-typed.
6, the printer always shows no paper or no ribbon when printing (TEC-572)
Cause: The paper has run out or the ribbon is wrong; the error operation command was sent.
Solution: Check if the paper or ribbon is correct; adjust the parameters on the machine, and then print correctly after using the printing software to correctly format the settings.
7. Printing is not clear when printing, and the ribbon is broken. (105Se/SL)
Cause: The printer ribbon hinge is faulty.
Solution: The belt tension of the machine ribbon is too tight, and the tension of the ribbon of the printer ribbon is adjusted.
8. The newly created file can be printed normally, but the old file cannot be opened and cannot be printed.
Cause: Network printing, permission is incorrect.
Solution: When printing, see if the file has been opened on the network. If it is turned on, it must be turned off before it can be opened on another computer. Then detect the network permissions issue.
9. The content is not completely printed when printing.
Cause: The printing software and driver version are too low.
Workaround: Install a new version of the software and drivers.
10. The software cannot be typeset.
Cause: The software is not installed or has a computer problem.
Solution: Reinstall the software, if it still doesn't work, it may be a virus in the computer, please kill the virus. No more, please reinstall the operating system.
11. Shortly after the machine is turned on, the three lights will go out and cannot be printed.
Cause: The printer capacitor is broken.
Solution: Replace the capacitor.
12. During the printing process, the printed content is not the same as the actual content.
Cause: The print driver is incorrect.
Workaround: Choose the correct printer driver.
13. Black lines appear next to the process. (argox1000+)
Cause: The print head is not adjusted.
Solution: Adjust the screws on the front of the printhead.
14, the machine is not turned back (TEC-572)
Cause: The setting is incorrect.
Solution: Adjust the various settings of the printer settings, if not, it may be a problem with the motherboard, need to be repaired.
15. Paper skipping often occurs during printing
Cause: The print settings are incorrect.
Solution: When the paper size and spacing settings are correct, change the BMP print format to PCX format for printing.
Welded Gabion
Stone filled baskets are called Gabions, Gabion baskets, Gabion wall etc. The usage of Welded gabion baskets are being accepted worldwide for soil prevention at river banks, ponds, lakes, sea coasts, bridges etc. Also welded Gabion Basket is being used for landscaping in residential town ships, universities, schools, public gardens, schools etc in today's life.
Anping
County CQ Wire Mesh Co., Ltd, established in 2007, and located in the
Hometown of Wire Mesh in China, is a professional leading manufacturer
engaged in the production and sale of Gabion, Gabion mattress, welded
gabion, Welded Wire Mesh, S.S. wire mesh etc.
Dedicated to strict quality control and thoughtful customer service, our
experienced staffs are always available to meet your requests. All of
our Gabions manufactured meet or exceed ASTM International standard, and
our products also have passed the ISO9001 Certificate with our high
quality. They have been exported to many countries, such as
USA, Australia, U.K, France, Italy, Philippines, Kenya, Thailand
etc until now.
Welded Gabion,Welded Gabion Basket,Welded Wire Mesh Panel,Galvanized Welded Gabion Basket
Anping Chuangqian Wire Mesh Co., Ltd , https://www.cqwiremesh.com